Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
We have uncovered this article on A Step-by-Step Guide to Installing a Bathtub directly below on the web and decided it made perfect sense to relate it with you on this page.
Setting up a bathtub isn't exactly rocket science, however it does require strong plumbing, woodworking, and sometimes, tiling skills. Replacing an old tub with a new one is additionally a moderately challenging project. If the old bathtub is readily accessible, the job can relocate immediately; if you have to open a wall surface to remove the old bathtub and also position the new tub, the job is much harder. In either situation, the project is within a house handyman's skills, although you will certainly need a helper to leave the old tub and also embeded in the new one. See to it you have certified yourself for the work as well as fit attempting it. As opposed to hiring a service provider to take over a halfway-completed project, it is better to consider using one before you begin. Opportunities are you may require a professional plumber to make tube links.
This short article will aid you install a brand-new bath tub in your washroom if you have actually already bought a brand-new bathtub and also do not need to alter the setup of your previous water pipes.
Your tools as well as product list must consist of the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your setup, after that the first thing you must do is detach the supply of water. After doing so, turn on the taps to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing taps can be quite troublesome due to the restricted accessibility that is often the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a cloth all set for the remaining water that will certainly come from the pipes. Once the supply pipelines have actually been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from transforming throughout this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any type of old sealing compound.
Prior to going on to fit the brand-new faucets, contrast the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will require lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the mounting opening in the bath/basin making sure that the washing machines remain in location between the tap and also the sink. Safeguard the tap in position with the producer provided backnut. When the tap is firmly in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet ports. The former kind must be attached to the faucet ends first, tightening just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Bathtub
Utilizing both wood boards under its feet, position the bathtub in the called for setting. The wood boards are useful in equally spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four little factors.
The following goal is to make certain that the tub is leveled all round. This can be attained by examining the spirit level and changing the feet on the bathtub up until the spirit level reads level.
To mount faucets, fit all-time low of the outermost versatile faucet connector to the proper supply pipeline by making a compression join; then do the exact same for the various other faucet.
Switch on the water system and also check all joints and new pipework for leaks as well as tighten them if needed. Load the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leaks.
Lastly, repair the bath paneling as described in the supplier's user's manual. Tiling and securing around the bathtub ought to wait up until the tub has been used at least once as this will resolve it right into its last setting.
Getting ready for the Installment
To start with, the supporting frame provided with the bathroom needs to be fitted (if called for) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets unit to prevent stress on the tub.
Fit the adaptable faucet connectors to the bottom of both taps using 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its final position.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, creating the water to pass through the wall in between the bathroom and the tiling, bring about issues with dampness and also possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes and also cartridges, and are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the bathtub with water prior to securing, to enable the movement experienced when the tub is in use. The sealer can fracture relatively very early if you do not take into account this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that write-up about Installing A Bathtub from a friend on a different web page. Do you know anybody else who is excited by the subject? Please feel free to share it. I value reading our article about How to Install a Bathtub.
Get Quote Report this page